Camass Series
Low Profile Cable Management Access Floor System

Camass Series

Camass is one of the most advanced access floor systems in the world market. Most contemporary low-profile access floors have to be fixed height. The Camass system can be installed at finish floor height 40 mm (1.57”), and height-adjustable by using of special “socket-set-screw” device. Overall system is light weighted and space-saving, which is especially designed and developed for office and school renovation and upgrading.
Safety:

●  Light weighted:
1/2 weight to conventional access floors.

●  Self-Stand:
Each UniPanel (main panel) is supported by four built-in pedestals at four corners of the panel body, self-stand and independent. In the event of earthquake or unusual lateral impact, no domino effect collapse will be occurred.  

●  Non-combustible:
full steel, suitable for using in metropolitan cities and high-rise buildings where non-combustibility is necessity.
Environment Friendly

● 
100 % recyclable: no cement infilled in the main access panel, all components of the system are 100% recyclable.  

●  100 % re-usable: in case of re-location, all components are re-useable.

●  LEED compliance: non-glue installation. No pollution, no damage to subfloor.
Grid-pattern cable trenches:

● 
Fully accessible cable trenches: 110 mm inside width, within every 600 mm.

● 
Cables are distributed and managed inside the Cable Trenches. Installing and re-routing of cables are easy, just by removing the cable trench caps.
Ideal for renovation and upgrading

Camass is ideal for office buildings’ upgrading, especially for early developed cities such as New York, Chicago, London, Paris,
Madrid, and so on. The system has also been chosen and installed for renovation projects in many prestigious educational institutions  
such as university libraries, museums, classrooms, and etc.
High changeability:

Installation can be proceeded at least interference to normal office operation. Reshaping or relocation is easy, fast, and at low cost than all other traditional access floors.
Camass photo 1
before
Camass photo 2
  installed
Camass photo 3
after
one of Time Warner sales office upgrading projects
Camass System

Internet and intranet are far beyond imagination of architects and developers who designed and/or built buildings in 1980s and before. Most office buildings built in 1980s and earlier, did not reserve height for raised access floor. In order to modernize those offices and school buildings, low-profile access floor is an effective solution for routing by large quantity of power and date cables above the sub-floors.

Camass System



Camass system has complete pedestal systems, which supporting finish floor height of access floor from supper low    
40 mm (1.57”) to 150 mm (6.0”). The system has effectively
retained maximum clearance in-between access floor and
ceiling, and in the meantime, provides large capacity for cable routing inside cable trenches.  

I    Super Low-Profile (with Set-Screw Locking device)                      

CA1000-40              40 mm (1.57”)                                                    
CA1000-60              60 mm (2.36”)     
                                              
II.    Low-Profile
            
CA1000-75              75 mm (3.0”)                                              
CA1000-100          100 mm (4.0”)
CA1000-135          135 mm (5.3”)
CA1000-175          175 mm (7.0”)
Camass panel photo 1

UniPanel with 4 built-in Pedestals
Camass panel photo 2
Description of components
    

The system consists of four main components:                              
UniPanel (main panel), Base Connector, Central Cap and Flank Cap.
                             
UniPanel (main panel): fully galvanized steel access panel. The panels are formed by special rivet process. There is no cement infilled. So, the panels are 100% recyclable. 
                                                                  
Self-standing: Each UniPanel has four built-in pedestals at four corners of the panel. Panels are self-stand. 

Size of UniPanel: 510 x 510 mm (20.07" x 20.07")
                                                                                                                        
Base Connector: to connect four UniPanels’ pedestals.
                                                                    
Central Cap: capping Cable Trench at intersection.
                                                                          
Flank Cap: capping Cable Trench at flanks of UniPanels.
Camass Components photo 1
Camass Components photo 2
Camass Components photo 3
Camass  photo 4

Cable Management & Accommodation


Once installed, the grid-pattern cable trenches spread overall the access flooring which consists of 90 mm wide (3.54”)  pening within every 600 mm (23.62”). Cables are distributed inside the Cable Trenches in order systematically. All exit of power and data wires are extended through the cable trenches directly, or by connected at the power sockets or data jacks in the service floor boxes installed at the cable trenches or the Outlet-Panels.
Efficient for cable extension and connection


Extension from the Cable Trench to workstation or
partition:
Power, voice and data cables are extended directly through the Exit-Cap, which is a Flank Cap consisted of 60 mm diameter pre-punched opening at one side. Grommet installed at the punched opening to protect the cables. The Exit-Cap option is efficient and cost-effective solutions for cable routing and extension.

Trench-type floor boxes to install at Cable Trenches
Netfloor Service Boxes SE403/SE603 (steel lid) and SS403/SS603 (stainless steel lid) serve to install at the cable trenches. Standard trench-type SE/SS403 floor box accommodates one 110V twin socket and 3 x Cat. 5 or Cat. 6 data jacks. And standard trench-type SE/SS603 floor boxes accommodates one 220V twin socket, and most other sockets in EC.
Camass Exit-cap photo
Cables extending through Exit-Cap to workstations or partition
Camass floorbox photo
Trench-type floor box installed on Cable Trench
Outlet-Panel to accommodate more compartments                    
To accommodate 3 or more compartments, Outlet-Panel by custom-made, cutting opening to required size at middle      
of the UniPanel to accommodate  

a.  Netfloor SB76 / SB60 Three compartments 4X220 volts sockets, 4  voice/data jacks.

b.  all international brands floor box such as MK, Britmac    
Spider, and etc. 
Camass floorbox photo
Camass floorbox photo
Outlet-Panel (opening in central of UniPanel) accommodates all types of floor boxes of 3 to 4 compartments

I. Super Low-Profile: system height 40 mm / 60 mm (1.57” / 2.36”)

CA1000-40 / CA1000-60 series
Camass super low-profile series consists of special “set-screw” pedestal system which supports access floor at low-height of 40 mm (1.57”). Although at low-height, the system can be adjustable, to ease deviation of the sub-floor which often occurred in old buildings.

Non-pollution: The UniPanels are self-stand. Pedestals are connected by Base Connectors. No adhesives shall be
glued onto the sub-floor. So, there is no pollution, no damage to subfloors at time of installation or re-location.  
System System height Cable Trench clearance height adjustment
CA1000W-40 40 mm (1.57”) 28 mm (1.10”) 38~55 mm (1.5”~2.16")
CA1000W-60 60 mm (2.36”) 48 mm (1.89”) 55~76 mm (2.16”~3")
(A) Clearance under cable trench: system height minus 12 mm (0.47”)
(B) Clearance under UniPanel: system height minus 28 mm
(C) Set-Screw: to lock pedestal from inside the socket set
Camass system height photo
Camass is only system applicable to install at 40~60 mm (1.57”~2.36”) height
CA1000-40 and CA1000-60 are installed by following the floor contour. The Cable trenches have effectively absorbed sub-floor deviation. Minor adjustment at pedestals from top, to set pedestals touch at ground to eliminate impact noise.
Clearance for cables routing under Cable trenches is maintained at steady height.
The below drawing (right) show Camass CA1000-40 system installed at finish floor height 40 mm (1.57”), which provides 28 mm (1.10”) clearance in cable trenches. For traditional access floors are not suitable to install at FFH lower than 100 mm (4”).
Camass system photo
Set-Screw Locking System for Super Low-Profile installation
The Set-Screw Locking System is a unique innovation by Netfloor, which is specially designed to enable installation at 40~60 mm (1.57”~2.36”) height.  
      
Set-Screw – factory assembled, inside pedestal’s socket set
●  Pedestal sets fixed at four corners of UniPanel
●  Set Screws are pre-embedded on top of the pedestals.  
●  Height adjustment:    
5 mm hex key wrench to loose and fasten the Set Screws.  
4 mm hex key wrench to adjust the pedestals’ height.
Camass system photo
Super Low-Profile 
Height adjustment – After finishing installation, floor deviation in certain areas may cause impact noise by the pedestals. Check by footstep. Minor adjustment of the pedestals shall be made to descend the pedestals at low points, or to ascend the pedestal to higher point, to touch the ground.

Step 1: To loose

Apply the 5 mm hex key wrench to loose the by counter-clockwise. Set-Screw by counter-clockwise.
Camass locking system photo
Camass locking tool photo


Step 2: To adjust height from top

Apply 4 mm hex-key wrench to adjust height by stretch through hollow hole of Socket-Set-Screw, insert at top of pedestal    
to adjust upward.
Camass locking system photo
Camass locking tool photo


Step 3: To fasten

Apply 5 mm hex-key wrench to fasten Socket Set Screw from top after adjustment For large job site installation, use mechanic tools for fastening.       
Camass locking system photo
Camass locking tool photo

II. Low-Profile system height 75mm~200mm (3”~8”)

CA1000-75 / CA1000-100 / CA1000-135 / CA1000-175
The low-profile series are suitable for offices where ceiling height is sufficient after installation of access floors. Camass low-profile series have been installing in many of new and old office buildings. 
      
Set-Screw – factory assembled, inside pedestal’s socket set
●  Pedestal sets fixed at four corners of UniPanel
●  Set Screws are pre-embedded on top of the pedestals.  
●  Height adjustment:    
5 mm hex key wrench to loose and fasten the Set Screws.  
4 mm hex key wrench to adjust the pedestals’ height.
Camass panel
Super Low-Profile 
System System height Cable Trench clearance height adjustment
CA1000-75 75 mm 63 mm 65~90 mm
CA1000-100 100 mm 88 mm 85~115 mm
CA1000-135 135 mm 123 mm 110~170 mm
CA1000-175 175 mm 163 mm 150~200 mm
(A) cable trench clearance: system height minus 12 mm (0.47”)
(B) clearance under UniPanel: system height minus 28 mm (1.10”)                    
(C) Lock-nut: To loose and fasten for height adjustment.                                              
(D) socket set T36 (36 mm (1.41”) L for CA1000-75 / CA1000-100)                                                                                                  
    socket set T60 (60 mm (2.36”) L for CA1000-135 / CA1000-175)
Camass system
Camass system photo
Set-Screw Locking System for Low-Profile installation
Assemble pedestal sets onto UniPanel    
Fix pedestal sets: For FFH 60 mm and higher height installation, pedestal-sets are assembled onto UniPanel at the job site. By using of rubber hammer, each UniPanel is fixed by 4 pedestal sets at four corners.
                                                                                                                         
In case of super low-profile, another option is to fix pedestal sets onto UniPanels at the factory or warehouse, stack, and ship to job sites for immediate installation.   
Decide the starting line, apply Base Connectors to connect                                                            
UniPanels. After connections, reticulated cable trenches formed automatically.

FFH greater than 100 mm (4”): laser alignment is recommended for height adjustment.

Install Central and Flank Caps on cable trenches every 3 or 4 rows. UniPanels connected and installed.
Camass system photo


Step 1: Loose the lock-nut

apply the 17 mm wrench to loose the lock-nut at bottom of the pedestal by counter-clockwise
Camass system photo
Camass locking tool photo


Step 2: Adjust height

apply the 4 mm hex key wrench, stretch at the hex hole at top of the pedestal, to adjust height from top.
Camass system photo
Camass locking tool photo


Step 3: To fasten

use the 17 mm wrench again, to fasten the lock-nut by clockwise.
Camass system photo
Camass locking tool photo
Why Camass ®  system is ideal solution for office and school modernization?

Nowadays, low-profile access floors have become a necessity in most of commercial and institutional interiors such as in offices, schools, libraries, museums, and so on. The conventional raised access floors (CRF), which are using in factories or data centers, have been slightly modified and to use in offices lately. Fundamentally, they are not suitable applications. The chart below is comparison made between Camass, other fixed height low-profile access floor, and the CRF. The chart has addressed many of the common issues.

Comparison: Camass / other fixed height low-profile / conventional access floor

advance \ product Camass Other low-profile Conventional access floor
Access panels full galvanized steel panel full galvanized steel panel(mostly) steel cementitious, woodcore
or calcium sulphate
Flammability non-combustible non-combustible non-combustible or class A
Modular size 600 mm X 600 mm(23.62"X23.62") 500X500 mm or other size(19.68”X19.68”) 600 mm X 600 mm or 610X610mm (24"X24")
System Weight avg. 24kg per M2 4.90 LB per sq. ft. avg. 24kg per M2 4.90 LB per sq. ft. avg. 45~ 55 kg per M2 9.2~11.24 LB per sq. ft.
clearance in low-profile  installation system height      clearance
40 mm                28 mm
60 mm                48 mm
75 mm                63 mm
100 mm              88 mm

N.A.  
system height      clearance
not suitable          not suitable
not suitable          not suitable
75 mm              not suitable
100 mm              avg. 68 mm
loading property light to medium traffic light traffic light to heavy traffic
cable  management reticulated cable trench 110 mm every 600 mm reticulated cable trench similar capacity no cable trench floor trunks required
cable exit free extension from fable Trench free extension from fable Trench difficult panels shall to be cut
height adjustable yes no yes
user-friendly yes yes not user-friendly
environmental-friendly yes, components 100 % reusable & recyclable yes, components 100 % reusable & recyclable
no, < 25 % recyclable   < 70% reusable
re-location cost "low", easy re-location "low", easy re-location "costly"
LEED compliance yes  pedestal non-glued onto sub-floor some yes, some not "doubt"  pedestal shall be glued onto sub-floor
suitable for retrofit projects yes light weight & low-profile yes light weight & low-profile not suitable heavy weight  
Low-Profile Access Floor
ECO
ECO

Low-Profile FFH 40, 50, 60, 70 mm
LEED Compliance
100% re-usable, 100% recyclable
Low-Profile Access Floor
CamassCrete
CamassCrete

Low-Profile Access Floor
Grid-Pattern Cable Trenches
100% re-usable, 50% recyclable
Low-profile Access Floor
GrandSquare
Grand Square

Low-Profile FFH 40, 60 mm
LEED Compliance
100% re-usable, 100% recyclable